Home - Gallery
- Contact - My upper floor - Videos -
Privacy Policy
ORIGAMI CHERRY BLOSSOM
I used papers of 9,5x9,5 centimeters or 3,5x3,5 inch for each single
flower
Step 1:
This paper is coloured on both sides.
Prefold over these 4 lines.
Step 2:
Make a valley-fold over these 4 lines.
Step 3:
Turn the model.
Step 4:
Make these folds from the edge of the
model
to the center, not any further.
First, make 2 valley-folds below, on the
right. Then, make
2 mountain-folds in the middle. And make
2 valley-folds
on the top left.
Step 5:
Pull the piece indicated by the arrow
upwards by
making a valley-fold over the green line.
Step 6:
Press the 2 layers indicated by the
smaller arrows
against each other. Then press the loose
piece flat
from above with your other hand, see
large arrow.
Step 7:
Make a valley-fold over these 2 lines.
Step 8:
Unfold the folds from step 7
Step 9:
Pull the edge indicated by the arrow
upwards by making
a valley-fold over the green line.
Step 10:
Press the edges that stand upwards flat
from above,
see arrows.
Step 11:
Fold the triangular piece above the
green line downwards
by making a valley-fold over this green
line.
Step 12:
Repeat step 6 to 11 on the other 3 loose
pieces,
see arrows.
Step 13:
Pull the 2 petals at the
bottom of the arrows outwards,
in the direction of these arrows.
Step 14:
Fold the triangular piece
above the green line to the
inside of the model by making a
mountain-fold over this
green line.
Step 15:
Push the 2 petals towards each
other again, see arrows.
Step 16:
Repeat step 13 to 15 on the
other 3 triangular pieces.
Step 17:
Push the 2 pieces indicated by the
arrows upwards by
making a valley-fold over the green line.
Step 18:
Pull the upper layer of paper (see
arrows) upwards,
loose from the rest of the model.
You can start pulling it loose on the
places indicated
by the arrows.
Step 19:
Make a valley-fold over these
(prefolded) lines.

Step 20:
Now you've made an extra petal.
Fold the petal upwards by making a
valley-fold over
the green line.

Step 21:
Make bookfolds until you see the same as
in the picture
of step 22
Step 22:
Make an inside reverse fold over these 3
lines. Do this
by making a mountain-fold over the short
line in the middle
and a valley-fold over the 2 outer lines.
Step 23:
Repeat step 22 on the 2 other same edges
of the model.
Step 24:
Make a valley-fold over the short green
line below and
a mountain-fold over the upper green
line.
Make the same folds on the other side of
the petal, see
small arrow.
Now you've folded the petal downwards in
the
direction of
the large arrow.
Step 25:
Repeat step 24 on the other 4 petals.
Step 26:
Make a mountain-fold on the tip of each
petal, see
the very short green lines.
Step 27:
Curl each petal backwards.
Step 28:
One flower is done...
Step 29:
This paper is for a branch, the backside
is white.
Fold it in half over the length a few
times.

Step 30:
Now, just fold or roll it up however you
want until you
get something like the one I made in
step 31.
Step 31:
One branch is done.
Use a smaller/shorter paper to make a
smaller/shorter branch.

Glue a few branches together.
Then glue as many flowers on it as you
want.



















